Beckhoff CB3053 Manuel d'utilisateur Page 66
- Page / 69
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Annex: Post-Codes
page 66 Beckhoff New Automation Technology CB3053
Code Description
49h 1. Determination of the entire memory size by revising the last 32-Bit double word of each 64k
memory segment.
2. Program “write allocation” at AMD K5-CPUs.
4Eh 1. Program MTRR at M1 CPUs
2. Initialise level 2-cache at CPUs of the class P6 and set the “cacheable range” of the random
access memory.
3. Initialise APIC at CPUs of the class P6.
4. Only for multiprocessor systems (MP platform): Setting of the “cacheable range” on the
respective smallest value (for the case of non-identical values).
50h Initialise USB interface
52h Testing of the entire random access memory and deleting of the extended memory (put on “0”)
55h Only for multi processor systems (MP platform): Indicate the number of CPUs.
57h 1. Indicate the plug and play logo
2. First ISA plug and play initialising – CSN-assignment for each identified ISA plug and play
device.
59h Initialise TrendMicro anti virus program code.
5Bh (Optional:) Indication of the possibility to start AWDFLASH.EXE (Flash ROM programming)
from the hard disk.
5Dh 1. Initialise Variable/Routine Init_Onboard_Super_IO.
2. Initialise Variable/Routine Init_Onbaord_AUDIO.
60h Release for starting the CMOS set-up (this means that before this step of POST, users are not
able to access the BIOS set-up).
65h Initialising of the PS/2 mouse.
67h Information concerning the size of random access memory for function call (INT 15h with
AX-Reg. = E820h).
69h Enable level 2 cache
6Bh Programming of the chip set register according to the BIOS set-up and auto-detection table.
6Dh 1. Assignment of resources for all ISA plug and play devices.
2. Assignment of the port address for onboard COM-ports (only if an automatic junction has
been defined in the setup).
6Fh 1. Initialising of the floppy controller
2. Programming of all relevant registers and variables (floppy and floppy controller).
73h Optional feature:
Call of AWDFLASH.EXE if:
- the AWDFLASH program was found on a disk in the floppy drive.
- the shortcut ALT+F2 was pressed.
75h Detection and installation of the IDE drives: HDD, LS120, ZIP, CDROM…
77h Detection of parallel and serial ports.
7Ah Co-processor is detected and enabled.
7Fh 1. Switch over to the text mode, the logo output is supported.
- Indication of possibly emerged errors. Waiting for keyboard entry.
- No errors emerged, respective F1 key was pressed (continue):
Deleting of the EPA- or own logo.
82h 1. Call the pointer to the “chip set power management”.
2. Load the text font of the EPA-logo (not if a complete picture is displayed)
3. If a password is set, it is asked here.
83h Saving of the data in the stack, back to CMOS.
84h Initialising of ISA plug and play boot drives (also Boot-ROMs)
85h 1. Final initialising of the USB-host.
2. At network PCs (Boot-ROM): Construction of a SYSID structure table
3. Backspace the scope presentation into the text mode
4. Initialise the ACPI table (top of memory).
5. Initialise and link ROMs on ISA cards
6. Assignment of PCI-IRQs
7. Initialising of the advanced power management (APM)
8. Set back the IRQ-register.
- Contents 3
- 0 Document History 5
- 1 Introduction 6
- ACUTE RISK OF INJURY! 7
- RISK OF INJURY! 7
- NOTE OR POINTER 7
- 1.3.3 Operator Requirements 8
- 1.4 Functional Range 9
- 2 Overview 10
- 3 Detailed Description 13
- 4 Connectors 14
- 4.1 Connector Map 15
- 4.2 Power Supply 16
- 4.3 Power Connector 17
- 4.4 System 18
- 4.5 External CMOS Battery 19
- 4.6 Memory 20
- 4.7 DVI 23
- 4.8 LVDS 24
- 4.9 Touch Screen 26
- 4.10 USB 1-4 27
- 4.11 USB 5-8 28
- 4.12 LAN 29
- 4.13 Audio 30
- CAUTION 31
- 4.16 SMB/I2C 33
- 4.17 Mini-PCI 34
- 4.18 Fan Connector 36
- 5 BIOS Settings 37
- 5.3 Standard CMOS Features 38
- 5.4 Advanced BIOS Features 40
- 5.4.1 CPU Feature 42
- 5.6 Integrated Peripherals 45
- 5.6.1 OnChip IDE Devices 46
- 5.6.2 Onboard Devices 47
- 5.6.3 SuperIO Devices 48
- 5.6.4 USB Device Setting 49
- 5.7 Power Management Setup 50
- 5.7.1 HPET Feature 51
- 5.7.2 Intel DTS Feature 52
- 5.8 PnP/PCI Configuration 53
- 5.8.1 IRQ Resources 54
- 5.9 PC Health Status 55
- 5.10 Load Fail-Safe Defaults 57
- 5.11 Load Optimized Defaults 57
- 5.12 Set Password 57
- 5.13 Save & Exit Setup 57
- 5.14 Exit Without Saving 57
- 6 BIOS update 58
- 7 Mechanical Drawing 59
- 7.2 PCB: Pin 1 Dimensions 60
- 7.3 PCB: Die Center 61
- 8 Technical Data 62
- 9 Support and Service 64
- I Annex: Post-Codes 65
- II Annex: Resources 68
- D PCI Devices 69
- E SMB Devices 69
Produits connexes et manuels pour Matériel Beckhoff CB3053
Matériel Beckhoff CB3060 Manuel d'utilisateur
(113 pages)
(113 pages)
Matériel Beckhoff CB3060 Manuel d'utilisateur
(113 pages)
(113 pages)
Canon PowerShot G2 manuales
Manuales del propietario y guías del usuario para Cámaras Bridge Canon PowerShot G2.
Ofrecemos 1 manuales en pdf Canon PowerShot G2 para descargar gratis por tipos de documentos: Manual de usuario
Commentaires sur ces manuels