Beckhoff BC3150 Manuel d'utilisateur Page 91
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Safety Instructions
Fieldbus Components 89
RS485
Fundamental
properties
RS-485 transmission according to the Profibus standard
Network topology Linear bus, active bus terminator at both
ends, stubs are possible.
Medium Screened twisted cable, screening may
be omitted, depending upon the
environmental conditions (EMC).
Number of stations 32 stations in each segment with no
repeater. Can be extended to 127
stations with repeater
Max. bus length without repeater 100 m at 12 Mbit/s
200 m at 1500 Kbit/s, up to 1.2 km at
93.75 Kbit/s
Max. bus length with repeater Line amplifiers, or repeaters, can
increase the bus length to the order of 10
km. The number of repeaters possible is
at least 3, and, depending on the
manufacturer, may be up to 10
Transmission speed 9.6, 19.2, 93.75, 187.5, 500, 1500 Kbit/s,
up to 12 Mbit/s, adjustable in stages
Plug connector 9-pin D-Sub connector for IP20
M12 round plugged connector for IP65/67
Cabling for
Profibus DP
and
Profibus
FMS
Setting of
station
addresses
The Profibus address must be set using the two rotary selection switches behind the
transparent cover. The default setting is 11. Any address is permitted, but each address may
only be used once within the network. The address is changed while the Fieldbus Box is
switched off. To do this, unscrew the cover and use a screwdriver to move the switches to the
desired position. Make sure that the switches engage properly. The change in address is
active as soon as the device is switched on.
Address Fieldbus Box
The switch on the left represents the tens, while that on the right represents the units.
Address Buscoupler
The switch S311 represents the tens, while that S310 represents the units.
- BC3150 - Bus Terminal 1
- Controller for PROFIBUS 1
- Contents 3
- 5. Programming 51 4
- 6. PROFIBUS 81 5
- 8. Appendix 97 5
- 1. Foreword 6
- Safety Rules 7
- State at Delivery 7
- Personnel Qualification 7
- Documentation Issue Status 8
- Firmware BC3150 8
- 2. Product Overview 9
- Safety Instructions 10
- 8 Fieldbus Components 10
- Fieldbus Components 9 11
- The interfaces 12
- Technical Data 13
- 12 Fieldbus Components 14
- Technical Data - PROFIBUS DP 15
- Technical Data - PLC 16
- 3. Mounting and Wiring 17
- Installation 18
- Potential groups 19
- PE power contacts 20
- Power contacts supply (Up) 21
- Power contacts 21
- KS2000-Z2 22
- M12 circular connector 23
- Nine pole D-Sub 23
- Profibus conductor colors 23
- 22 Fieldbus Components 24
- Cable-based transmission 25
- Distances 26
- Bus segments 26
- Installation guidelines 26
- Checking the Profibus wiring 26
- Fieldbus Components 25 27
- Setting the slave address 28
- Configuration 29
- Configuration types 29
- 28 Fieldbus Components 30
- Creating a BX File 31
- Selecting the target system 32
- Fieldbus Components 31 33
- Fieldbus Components 33 35
- Mapping code 36
- Data memory mapping 36
- Used code and data memory 37
- Other memory 37
- Reading AMS Net ID 38
- PROFIBUS 39
- Master Configuration 40
- DEFAULT CONFIG 41
- Opening an existing BX file 41
- 40 Fieldbus Components 42
- Fieldbus Components 41 43
- Inserting the images 44
- Inserting the GSD files 44
- BX3100 parameter data 45
- BX3100 module configuration 46
- Fieldbus Components 45 47
- 46 Fieldbus Components 48
- K-Bus variables 49
- Inserting a PLC project 50
- Measuring the PLC Cycle Time 51
- 50 Fieldbus Components 52
- 5. Programming 53
- TwinCAT PLC 54
- Online Change 54
- TwinCAT PLC error codes 55
- Error POUs 55
- Global memory error 56
- Remanent data 57
- Allocated Flags 58
- Example structure 59
- 58 Fieldbus Components 60
- Mapping of the Bus Terminals 61
- 60 Fieldbus Components 62
- Creating a boot project 63
- PLC Control 63
- Deleting a boot project 63
- 62 Fieldbus Components 64
- General Settings 65
- Downloading a program 66
- Uploading a program 67
- Password 68
- Libraries 69
- Download 69
- TcSystemBCxx50 69
- 68 Fieldbus Components 70
- TcBaseBX 71
- System task info type 72
- System Info 73
- System Info Type 74
- Local ADS Port Numbers 75
- Register port 100 76
- Start Debug Timer function 77
- Read Debug Timer function 77
- Example 77
- Program Transmission 78
- Fieldbus Components 77 79
- Transmission via PROFIBUS 80
- Fieldbus Components 79 81
- Process Image 82
- TWINCAT CONFIG 82
- 6. PROFIBUS 83
- Diagnostic functions 84
- Sync and Freeze Mode 85
- System behavior 85
- Protection mechanisms 86
- Ident number 86
- DP StartUp 87
- Cyclic data exchange 87
- States in the master 88
- PROFIBUS DPV1 89
- Cables, Plugs and Switches 90
- Fieldbus Components 89 91
- 90 Fieldbus Components 92
- Topology 93
- Diagnostics 94
- PROFIBUS state 94
- State of the K-Bus 95
- Diagnostic LEDs 96
- LEDs for K-Bus diagnostics 96
- LED bus - fieldbus diagnosis 97
- LED PLC - PLC diagnosis 98
- 8. Appendix 99
- Program description 100
- Moving from BCxx00 to BCxx50 101
- Moving from BCxx00 to BXxx00 102
- Retain data 103
- Allocated variables 103
- Task configuration 103
- Firmware Update 104
- Firmware update program 104
- Safety Instructions 105
- Fieldbus Components 103 105
- 104 Fieldbus Components 106
- General Operating Conditions 107
- Environmental conditions 107
- Component identification 108
- Standards for Device Testing 109
- Vibration / Shock resistance 109
- Bibliography 110
- German books 110
- English books 110
- PROFIBUS-DP standards 110
- Web sites 110
- List of Abbreviations 111
- Support and Service 112
- Beckhoff Support 112
- Beckhoff Service 112
- Beckhoff Headquarters 112
Produits connexes et manuels pour Équipement Beckhoff BC3150
Équipement Beckhoff BC3150 Manuel d'utilisateur
(115 pages)
(115 pages)
(2 pages)
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.316 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels