Beckhoff BC3150 Manuel d'utilisateur Page 63
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Safety Instructions
Fieldbus Components 61
Creating a boot project
Approximately 250 kB of flash are available.
For creating a boot project
•
on the Bus Terminal Controller of BX-Series app. 250 kByte of flash are available
•
on the Bus Terminal Controller of BCxx50-Series app. 48 kByte of flash are available
PLC Control
After logging in, a boot project can be created in TwinCAT PLC Control.
•
Opening a PLC project
•
Selecting the target system (or selection the serial interface)
•
BX/BCxx50 login
•
Creating the boot project (Online\Create boot project)
Once a valid boot project is present on the BX/BCxx50 controller, the green PLC LED is on.
At the Bus Terminal Controller of BX-Series the PLC LED will flash orange during the creation of the boot project. If
no boot project is available on the BX the PLC LED shines orange.
Deleting a boot project
A boot project can be deleted from the BX/BCxx50. The following steps must be followed:
•
Opening the project
•
BX/BCxx50 login
•
Deleting the boot project (Online\Delete boot project)
Once the boot project was deleted, the PLC LED will be orange.
Note
After an online change, the boot project is still the old project. To use the current project
(after the online change) as the boot project, the boot project has to be recreated.
Bypassing the start of the boot project*
At the Bus Terminal Controller of BX-Series the start up of an existing boot project can be avoided by pressing the
Navi switch during booting. This will not delete the boot project. The project can still be used when the controller is
switched on again.
* from version 0.85
- BC3150 - Bus Terminal 1
- Controller for PROFIBUS 1
- Contents 3
- 5. Programming 51 4
- 6. PROFIBUS 81 5
- 8. Appendix 97 5
- 1. Foreword 6
- Safety Rules 7
- State at Delivery 7
- Personnel Qualification 7
- Documentation Issue Status 8
- Firmware BC3150 8
- 2. Product Overview 9
- Safety Instructions 10
- 8 Fieldbus Components 10
- Fieldbus Components 9 11
- The interfaces 12
- Technical Data 13
- 12 Fieldbus Components 14
- Technical Data - PROFIBUS DP 15
- Technical Data - PLC 16
- 3. Mounting and Wiring 17
- Installation 18
- Potential groups 19
- PE power contacts 20
- Power contacts supply (Up) 21
- Power contacts 21
- KS2000-Z2 22
- M12 circular connector 23
- Nine pole D-Sub 23
- Profibus conductor colors 23
- 22 Fieldbus Components 24
- Cable-based transmission 25
- Distances 26
- Bus segments 26
- Installation guidelines 26
- Checking the Profibus wiring 26
- Fieldbus Components 25 27
- Setting the slave address 28
- Configuration 29
- Configuration types 29
- 28 Fieldbus Components 30
- Creating a BX File 31
- Selecting the target system 32
- Fieldbus Components 31 33
- Fieldbus Components 33 35
- Mapping code 36
- Data memory mapping 36
- Used code and data memory 37
- Other memory 37
- Reading AMS Net ID 38
- PROFIBUS 39
- Master Configuration 40
- DEFAULT CONFIG 41
- Opening an existing BX file 41
- 40 Fieldbus Components 42
- Fieldbus Components 41 43
- Inserting the images 44
- Inserting the GSD files 44
- BX3100 parameter data 45
- BX3100 module configuration 46
- Fieldbus Components 45 47
- 46 Fieldbus Components 48
- K-Bus variables 49
- Inserting a PLC project 50
- Measuring the PLC Cycle Time 51
- 50 Fieldbus Components 52
- 5. Programming 53
- TwinCAT PLC 54
- Online Change 54
- TwinCAT PLC error codes 55
- Error POUs 55
- Global memory error 56
- Remanent data 57
- Allocated Flags 58
- Example structure 59
- 58 Fieldbus Components 60
- Mapping of the Bus Terminals 61
- 60 Fieldbus Components 62
- Creating a boot project 63
- PLC Control 63
- Deleting a boot project 63
- 62 Fieldbus Components 64
- General Settings 65
- Downloading a program 66
- Uploading a program 67
- Password 68
- Libraries 69
- Download 69
- TcSystemBCxx50 69
- 68 Fieldbus Components 70
- TcBaseBX 71
- System task info type 72
- System Info 73
- System Info Type 74
- Local ADS Port Numbers 75
- Register port 100 76
- Start Debug Timer function 77
- Read Debug Timer function 77
- Example 77
- Program Transmission 78
- Fieldbus Components 77 79
- Transmission via PROFIBUS 80
- Fieldbus Components 79 81
- Process Image 82
- TWINCAT CONFIG 82
- 6. PROFIBUS 83
- Diagnostic functions 84
- Sync and Freeze Mode 85
- System behavior 85
- Protection mechanisms 86
- Ident number 86
- DP StartUp 87
- Cyclic data exchange 87
- States in the master 88
- PROFIBUS DPV1 89
- Cables, Plugs and Switches 90
- Fieldbus Components 89 91
- 90 Fieldbus Components 92
- Topology 93
- Diagnostics 94
- PROFIBUS state 94
- State of the K-Bus 95
- Diagnostic LEDs 96
- LEDs for K-Bus diagnostics 96
- LED bus - fieldbus diagnosis 97
- LED PLC - PLC diagnosis 98
- 8. Appendix 99
- Program description 100
- Moving from BCxx00 to BCxx50 101
- Moving from BCxx00 to BXxx00 102
- Retain data 103
- Allocated variables 103
- Task configuration 103
- Firmware Update 104
- Firmware update program 104
- Safety Instructions 105
- Fieldbus Components 103 105
- 104 Fieldbus Components 106
- General Operating Conditions 107
- Environmental conditions 107
- Component identification 108
- Standards for Device Testing 109
- Vibration / Shock resistance 109
- Bibliography 110
- German books 110
- English books 110
- PROFIBUS-DP standards 110
- Web sites 110
- List of Abbreviations 111
- Support and Service 112
- Beckhoff Support 112
- Beckhoff Service 112
- Beckhoff Headquarters 112
Produits connexes et manuels pour Équipement Beckhoff BC3150
Équipement Beckhoff BC3150 Manuel d'utilisateur
(115 pages)
(115 pages)
(2 pages)
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.626 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels