Beckhoff AX2000 Manuel d'utilisateur Page 5
- Page / 11
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
If you want to use the position control of the servo amplifier, then you must enter the specific
parameters for your drive:
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
Axis type :
- Click on the POSITION button
- Click on the POSITION DATA button
- Select the axis type (linear or rotary)
Resolution :
- Enter the denominator and numerator for the resolution. Here you adjust the path
traversed by the load in positioning units (length unit for linear axes, or °mech.
for rotary axes) to match the number of turns of the motor.
Only integer entries are permitted.
Example 1: Ratio = 3.333
mm / turn
=> resolution = 10000/3 µm/turn (all other path entries in µm)
or
=> resolution = 10/3 mm/turn (all other path entries in mm)
Example 2: Ratio = 180 °mech./turn
=> resolution = 180/1 °mech./turn (all other path entries in °mech)
vmax :
- Enter the maximum traversing speed for the load that results from the resolution
at the rated speed of the motor. The dimensional unit is derived from the
resolution (°mech./sec or length units/sec).
Example 1: resolution = 10000/3 µm/turn, n
nom
= 3000 turns/min
=> vmax = resolution * n
nom
= 10000/3 * 3000 µm/min = 10 000 000 µm/min
or
=> vmax = resolution * n
nom
= 10/3 * 3000 mm/min = 10 000 mm/min
Example 2: resolution = 180 °mech/turn, n
nom
= 3000 turns/min
=> vmax = resolution * n
nom
= 180 * 3000 °mech/min = 9000 °mech/s
t_acc/dec_min :
- Enter the time in ms that the drive requires, with the
mechanically permissible maximum acceleration,
to accelerate from zero speed to vmax.
InPosition :
- Enter the window for InPosition. This value is used for the InPosition message.
The dimensional unit is derived from the resolution
(°mech. or length unit).
Typical value : e.g. approx. resolution * 1/100 turn
- Clicken on APPLY and then on OK
- Answer the query “Save to EEPROM/Reset” with NO
(the data are in the RAM and will be permanently stored later)
max. following error :
- You now see the screen page POSITION
- Enter the window for the following error. This value is used for the message
FOLLOWING ERROR. The dimensional unit is derived from the resolution
(°mech. or length unit).
Typical value : e.g. approx. resolution * 1/10 turn
Save parameters :
- Click on the button
- Answer the query RESET AMPLIFIER with YES
Quick Start 5
BECKHOFF 06.00 Parameterization
- Edition 06/00 1
- 06.00 General 3
- II.3 Basic parameterization 4
- 4 Quick Start 4
- Quick Start 5 5
- 06.00 BECKHOFF 6
- Quick Start 7 7
- III.5.1 Preparation 8
- 8 Quick Start 8
- III.5.2 Optimization 9
- Quick Start 9 9
- 10 Quick Start 10
- Optimization 06.00 BECKHOFF 10
- Quick Start 11 11
- BECKHOFF 06.00 Optimization 11
Produits connexes et manuels pour Équipement Beckhoff AX2000
(11 pages)
(11 pages)
(51 pages)Greenheck Fan Fans Benutzerhandbücher
Beginnend mit S
Commentaires sur ces manuels